NEW...... $180 P/N ET355 Features: 1. Polarized/Retro-Reflective type photocell What does this mean 2. Red infrared led element 3. Sensing range adjustable (optional) 4. IP-66 water proof 5. IP-66 water proof cable gland 6. PMMA upper casing, anti fog/dew/rains 7. Round shape reflector-Dia.: 80mm 8. Input volt.: AC/DC 12~250V 9. Twin colours Led indicator for beam alignment 10. Tamper switches included Sensing Range up to 10 Meters
Very Important! Please Read! You should always have a qualified electrician work with 240V power. Never attempt any wiring with 240V mains power by yourself!
240V wiring blue should be neutral and brown should be live! Consider others when they work on live wires in the future! I personally have been given a nasty shock a result of someone using the earth wire as a live feed.
Safety Photo Cells
Used as a safety device. Protects by sensing person or vehicle in danger zones. Operate at a distance up to 295'. When infrared beam is broken it produces a detection signal to stop or reverse a gate. Used primarily with gate operators. Can be used in sets to protect all areas of entrapment
Just think of the unpleasant results of you driving your car through your gate, when it suddenly decides to close! With a photo cell, anything that breaks the beam will stop and reverse the gate. And when we say anything, we mean anything, people included! I rate this as a must have option for any gate.
Tip: On most gate motors there is a special outlet for Photo Safety Beams on the control board. “Normally Open” and “Normally Closed” are words that you'll come across when many accessories to gate motors. “Normally Closed” Designation which states that the contacts of a switch or relay are closed or connected when at rest. When activated, the contacts open or separated.
Use “Normally Closed” when installing Photo Safety Beams! When someone passes through the inferred beam the circuit is broken. “Normally Open”: Designation which states that the contacts of a switch or relay are normally open or not connected. When activated the contacts close or become connected Non Polarity means they are reversible.
When wiring photo cells to your gate you will require 4 wire cables: 2 for power, 1 to common (earth) and 1 for normally closed outlets on the control board.
Infrared beam security beam sensor. (Waterproof) the PE sensor is safety beam sensor, Are used on gates and garages opening systems to stop the gates from closing on a car, person or objects, Specifications Detection technology: Infrared Range: 15m Frequency: 1.92Khz Power: 12-24V AC/DC Wave Length: 940mm Input: RX 15mA, TX 30mA Operating temperature: -20 to 70 degrees Relay output: 1Amp max 30V Dimension: 49.2 x 76 21mm Please note: The range give above may vary according to the site environment conditions and according to the weather
$59.00 P/N ET405
Photo cells are designed for safety!
Applications: 1. Gate Automation 2. Overhead door 3. Swing gate 4. Sliding door 5. Perimeter Protection 6. Window Security Protection 7. Terrace 8. Warehouse 9. Parking lot 10. Entry Alert
A bit of Fun - not for this owner
How Polarized Sensors Work:The transmitted IR light that the sensor emits is polarized in a certain direction. When shiny objects pass in front of the transmitted beam, they reflect light into a polarized filter. Only light that matches the original polarization will pass into the receiver.
$109.00 - P/N ET409
Nice Era (BlueBus System) only to be used with Nice Motors Photocells M Beams (Waterproof) Made in Italy EPMB
* An antiglare circuit which eliminates possible sunlight interference. * 10 degree angle of reception * ABS body that is resistant to all conditions * 2 range levels * Estimated range of 15m
ABN 96 205 178 715 - Fax: 03 8640 0791 - E-Mail: email@example.com REGISTERED STEEL MEMBER BlueScope is a trademark of BlueScope Steel Limited COLORBOND® is a brand name (Trade Mark) of Bluescope Steel Ltd - We delivery to, New South Wales, Queensland, Victoria, Tasmania, South Australia, Western Australia, ACT, Northern Territory